IEC Testing

 

IEC-TR-61282

Experior Lab’s is capable of testing enclosures for electrical systems per IEC 61282. Also, known as EN 62262, the standard classifies IK rating, which is defined as the level of protection that enclosures provide against mechanic impacts from outside.

 

 

IEC 62262

Experior Lab’s is capable of testing enclosures for electrical systems per IEC 62262. Also, known as EN 62262, the standard classifies IK rating, which is defined as the level of protection that enclosures provide against mechanic impacts from outside.

 

IEC 62005

Experior’s facility can handle reliability testing for the IEC 62005 series of standards. Reliability testing varies from product to product but this series is specific to fiber optic interconnection devices and passive components. Some issues cover life stress modeling (IEC 62005-7) while others cover aging, tests, temperature, and humidity.

 

IEC 61755

Experior’s test lab can test a wide range of fiber optic devices, components, and subsystems. IEC 61755 covers fiber optic interconnection devices and passive components. Specific issues cover specific components. For example, IEC 61755-3-1 covers single mode, PC ferrule, while IEC 61755-3-2 covers the same but APC ferrule.

 

IEC 61754

Experior Lab’s can test fiber optic connector interfaces to the IEC 61754 series of standards. All connector interfaces are covered such as FC-PC, mini-MPO, MT-RJ, etc.

 

IEC 61753

Experior Lab’s has the expertise to test many of the IEC 61753 family of standards. Fiber optic interconnecting devices and passive components are areas of our expertise. Components such as closures, attenuators, and connectors are covered.

 

IEC 61300

Experior Lab’s can test fiber optic interconnecting devices and passive components to the IEC 61300 family of standards. Connectors, mating adapters, and other interconnective devices can be tested, examined, and measured.

 

IEC 61280

Experior Lab’s has extensive experience in IEC 61280 testing of fiber optic subsystems.

 

IEC 61000

Experior Laboratories has the capability to test and measure EMC to the IEC 61000 family of standards. The EMC standards cover disturbances, variations, and voltages fluctuations among other properties.

 

IEC 60794

Experior Lab’s has the expertise to test many of the IEC 60794 family of standards. Both indoor and outdoor cables are covered ranging from multi-optical fibers, buried cables, aerial cables, etc. For general measurements, one would follow IEC 60794-1-2 as it covers basic optical test procedure.

 

IEC 60695

Experior Lab’s can conduct fire hazard testing to IEC 60695. This series of international standards cover test methods to flame, abnormal heat and other fire test for electromechanical products.

 

IEC 60512

Experior Laboratories can conduct IEC 60512 testing of connectors for electronic equipment. Connectors and contacts are tested to environmental and mechanical stress to determine if the product still functions properly. General examination, ,dimensions and performance testing is conducted as well.

 

IEC 60068

Experior Laboratories has the capability to conduct environmental testing on electrical equipment and components to the IEC-60068 series of international standards. Also titled BS EN 60068, the series provides standard procedures to determine any weakness or degradation, during or after a test. Each document is specific to a test such as IEC 60068 Part 2-6 Sinusoidal Vibration, Part 2-31 Rough Handling Shock, or Part 2-38 Composite Temperature/Humidity Cyclic Test.

 

 

ETSI EN 300 019

Experior Lab’s has the capability to conduct a number of the test standards, severities, and methods described in the EN 300 019 series of documents. This series specifies the environmental tests for telecommunications equipment when in storage, in transportation, or in use. The “in use” can further be categorized as stationary, mobile, or both. Experior has extensive experience in stress and environmental testing for telecom components, devices, and products.

 

IEC 60529

Experior Laboratories can conduct IEC 60512 testing of connectors for electronic equipment. Connectors and contacts are tested to environmental and mechanical stress to determine if the product still functions properly. General examination, ,dimensions and performance testing is conducted as well.

 

Contact Experior Today To Learn More About Our Testing Capabilites

805-483-3400